Grounding exterior cables is equally as crucial as selecting the best cables for the television or Internet system. Grounding may prevent shocks from lightning strikes and surges from shooting across your coaxial cable and into the back of your television or Internet system. It’s also not very complicated: anyone capable of connecting 1/2” Foam Cable can ground that very same cable to an pre-existing electrical ground with little trouble.

Any television system with wires running outdoors should ground them. Attach the grounding block to your home, somewhere close to where the coaxial cable will come in. A grounding block could have at least two screw holes; drill holes for every, then secure the block to the wall with all the included screws.

Disconnect the coaxial cable through the splitter and hook it up to one side in the grounding block. This can be done by simply twisting the end until it appears loose. Lightly coat the ports on the grounding block using the silicone grease. This can assist in weatherproofing the ports. Do the same for virtually any open ports on the coaxial splitter.

Connect a whole new RG-6 coaxial cable to the level on the splitter where the previous cable was disconnected. Then attach the other end in the cable for the other side in the grounding block. Coaxial cables attach by inserting the pin from the middle of the cable into the pin-sized hole on the port, then twisting the cable until it secures set up.

Attach the grounding wire towards the grounding screw on the grounding block. Loop the wire around the screw and twist the screw in till the wire is secure. Then run the wire towards the electrical ground and attach the wire there in the same way. If no screw is available, twist the conclusion of the cable around the ground as tightly as is possible; crimping with pliers if needed.

Before I get into how and why you should ground your antenna, I needed to let you know I am just not an electrician. I’m a DIY weekend warrior that depends on Google search-fu to learn how to do household repairs and installs.

For any engineers or electricians that drop by, I welcome any critiques or corrections in the comments. Accuracy is extremely important for me, and i also appreciate any corrections or adjustments it is possible to offer.

Nevertheless, many years of employed in enterprise architecture make me somewhat of a stickler for standards and practices. Should you be also, you may want to have a look at Article 810 of the National Electric Code. It covers all the codes and standards for installing the cabling for TV and radio transmitters.

However, should you be like many people, you’d rather hit your thumb repeatedly with a hammer than suffer through technical manuals. In that case, I’ll do my better to walk you through what I did after looking over the code.

Below is actually a picture describing exactly what we will do. It illustrates how to ground your antenna by connecting it to your house’s ground wire. Notice you must not only ground the Coaxial Cable Grounding Kit, nevertheless the antenna mast too.

Grounding an antenna isn’t difficult to accomplish yourself, but it shouldn’t be expensive to possess a professional appear and accomplish this to suit your needs. If you want to attempt this, below are would be the steps I took to recreate precisely what is essentially depicted in the diagram.

Cable installation basics. Install equipment and cabling in a neat and workmanlike manner [820.24]. You can find the industry practices described in ANSI/NECA/BICSI 568, Standard for Installing Commercial Building Telecommunications Cabling.

Exposed cables should be supported by the structural components of your building to prevent cable damage as a result of normal building use. Secure cables with straps, staples, hangers, or similar fittings designed and fmpuqh so as not to damage the cable.

Cables run parallel to framing members or furring strips must be protected where they could be penetrated by nails or screws. To offer this protection, you have two options. Install the cables at least 1¼ inches through the nearest edge of the framing member or furring strips.

Protect the Feeder Clamp with a 1/16-inch-thick steel plate Wiring support rules for coaxial cables can be a little tricky. Make sure you know when and where independent support wires must be used. You must securely fasten raceways which contain coaxial cables in position. Don’t use ceiling-support wires or perhaps the ceiling grid to back up raceways or cables. It is possible to, however, support raceways and cables with independent support wires attached to the suspended ceiling.